THIS IS A NEW SITE AND IT TAKES A WHILE TO GATHER ALL THE "COTTAGE"  PEOPLE - SO PLEASE COME BACK REGULARLY AS HOPEFULLY WE WILL BE GETTING MORE ITEMS
There are many British marques and below is a list gathered from several sources.  Additions are most welcome!

AC, Allard, Alta, Alvis, Armstrong-Siddeley, Arnolt, Aston Martin, Austin, Austin Healey, Bedford, Bentley, Berkley, Bond, Bristol, Brough-Superior, BSA, Caterham. Clan,  Commer, Costin, Crossley,  Nathan, Daimler, Davrian, Diva, Elva, Falcon, Ford, Frazer-Nash, Gilbern, Ginetta, Gordon-Keeble, Healey, Hillman, HRG, Humber, Jaguar, Jensen, Jowett, Jensen-Healey, Kieft, Lagonda, Lea Francis, Lister, Lola, Lotus, Marcos, MacLaren, MG, Morgan, Panther, Peel, Peerless, Reliant, Riley, Rover, Salmson, Singer, Standard, Sunbeam, Tojeiro, Triumph, Turner, TVR, Vauxhall, Warwick, Westfield, Wolseley, WSM

This web site is devoted to enthusiasts who have developed items that may be of interest to primarily British car enthusiasts.  
It is not intended to be a site promoting products that are normally commercially available.    
For further information on being listed please email to:  CLICK HERE

Please note prices do not include shipping and handling.  Prices are subject to change without notice.

www.britishcarlinks.com          The V8 Register         www.team.net
www.sumpy.com                      www-restored-classics.com

These O-rings can be used to refurbish standard Smith and Jaeger gauges as found on British classic cars as well as some foreign cars.   The “dash to bezel” or “outer” rings are round cross-sectioned rubber as used on the originals but their high quality means they will last much longer.  

The “glass to bezel” or “inner” rings should be replaced also.  The original inner rings often turn into  brittle tar over the years and allow ingress of moisture and dust.  It is important to remove all traces of the old O-ring before using these replacements.   Because these replacements are made from closed-cell sponge rubber they will fit better than the originals and provide increased sealing.  Some gauges have slight differences, especially Jaeger gauges but the sponge rubber inner rings adapt easily to cater for these differences.  

There are only four sizes of the commonly used gauges.  These are 52mm (2"), 80mm (3"), 100mm (4") and 120mm (4.75").  To determine a gauge size measure the hole in the dash or the gauge's body size.

It has been known for Jaeger gauges to be relabeled as Smith gauges.

 The paper washers as used in some gauges are not available.

      Please e-mail enquiries to: CLICK HERE

These grille inserts are made from quality stainless steel mesh and are cut to fit MGBs with the chromed surround.  The rubber gasket prevents rattles and chafing.  Although mounting holes are provided there may be a need for some easy fettling as not all surrounds are the same.   The mesh is high quality material as used in the food and medical industry.  The size of mesh shown has now been superceded by thicker and more widely space mesh.  

Because of their length the postage costs are relatively high, and  while lower cost can be achieved by supplying in two halves, this is NOT recommended.

Only one side is polished.

Price subject to change without notice.

   Price  US$60 plus postage

Please e-mail enquiries to: CLICK HERE

Installing this material where there is little room to manoeuver can be quite difficult as the aggressive adhesive means placing it in the exact location required.  It requires patience and some "wall-papering" skills.  Installing on a flat, readily accessible surface is, however, very easy.

There are two types of material available.  One is "Single layer" and consists of one layer of heat reflecting aluminium foil and one layer of polymer bitumastic to deaden sound.  It has an aggressive adhesive covered by a removable wax paper.  The other "multi-layer" material consists of two layers of the single material with a closed cell high density foam sandwiched between (see left).   This has excellent sound deadening properties with double the heat resistance.

The single layer material is easily applied to curved surfaces but the multi-layer  usually has to be applied in two pieces; the first being a layer with the foam that can be molded to the surface, then a single layer applied on top of it.   This results in a smooth contour-following finish.

Applying the material to the door skins can have a dramatic effect and turns "clinks' to "clunks" as found on the more expensive cars.  However, installing the multi-layer material to the door skin is better achieved when the winding mechanism and glass are not fitted.

The photo shows single layer material installed.  The multi-layer was installed on the door skin before fitting the winding mechanism and glass.  The multi-layer installed on the skin helps reduce the appearance of the "crack of doom" on MGBs.

The material over the door 'holes' can be cut out to gain access to the mechanical parts and then patched with spare material to provide water proofing to interior panel.

An effective sound deadening result can be achieved by laying the multi-layer material on the car's floor. The first layer is the half that has the foam and this can be pushed down on the floor to follow the contours  and provide the maximum sound deadening.  Then the one piece single material top layer is put over the top.   This top layer can be fashioned to have a two inch "lip" resulting in a waterproof well.  Because the foam does not absorb moisture it will dry out quickly even if the cockpit is drenched above the two inch protective lip.  However, fitting the top layer requires getting it in the correct position before removing the wax paper covering the adhesive.  Not a difficult task but one not to be done in a hurry!

This method can be applied to cover the foot wells giving excellent sound proofing and heat exclusion in the cockpit.

   Prices  US$4/sqft (single layer)  
                US$8/sqft  (multiple layer)

Please e-mail enquiries to:  CLICK HERE

This gear shift knob is for the enthusiast who has everything!  They are turned from ancient wood dug out from the peat where the tree has lain for approximately 50,000 years.   The wood has a peculiar amber coloured depth - almost as if it were made from a particularly old cognac.  This is seen from certain angles and is unique.  The effect is almost the same as when viewing the adjacent picture on the screen at different angles.

Each knob is identified by age as each tree is carbon dated and a copy of the test is given with each knob.  The knobs can be ordered with round or flat tops.  The latter allows logos of shift patterns to be attached.  They have 1/2 inch holes at the bottom so that the correct fitting can be glued in to accommodate the gear shift lever.  These bits of hardware are readily available from hardware stores and cost pennies.   Unfortunately they cannot be provided with the knob due to the different threads of gear shift levers.

Price subject to change without notice.

       Price US$50  plus postage

Please e-mail enquiries to: CLICK HERE

Pensbury Manor Garage's  GREAT  KNOBS dressing re-blackens the oxidized, faded and browned-out color of your dash knobs, switches, brake handles, gear shift knobs, horn buttons and many other rubber and vinyl items. GREAT KNOBS!  is a dye that penetrates the rubber surface pores and bonds with the original rubber in a most satisfactory way.  It is a water based, black liquid dye that bonds with rubber but will not bond with the metal so clean up is a snap.   The resulting restored color can be hand buffed to a very high sheen.  GREAT KNOBS! uses the same colouring agent that was used when the knobs were originally made. 
Pensbury Manor's GREAT KNOBS! can be ordered by mail or online. 
Pensbury Manor Garage's GREAT KNOBS comes in  2 sizes - enough to restore from 25 to 50 normal size knobs and switches or more. Go to the Web Siteto learn more or to order.

Web Site: CLICK HERE

Please e-mail enquiries to: CLICK HERE

Web Site CLICK HERE

These plates give you the extra points you need for your concours car, or just that finishing touch on your daily driver.

There are MGA 1500 and MGA 1600 and MGTF plates available.

The price for these plates is 27 euro's including shipping worldwide

Payments can be made by PayPal

Web site CLICK HERE

Please email enquiries to: CLICK HERE